NALTIC Industrials, LLC

ARDROX 2871 Paint Stripper – Remover

Ardrox 2871 is a peroxide-accelerated non-acid paint remover-stripper.  It is designed to remove durable paint systems, such as epoxy and polyurethane, from aircraft and other surfaces. It contains no halognenated solvents, and its combination of near neutral pH and low odor make it an excellent choice in areas personnel are working

A Product of Chemetall U.S., Inc.

TECHNICAL DATA

Appearance: Viscous, yellow emulsion
Odor: Characteristic
Density at 20°C: 1.02-1.05 g/mL
Flash Point: >100 °C

APPLICATION

Concentration: Ardrox is ready for use as supplied.

Preparation: Prior to the application of Ardrox 2817, any surface materials requiring masking should be accommodated. Consult your OEM or internal documentation for the appropriate masking procedures. Best results will be achieved at temperatures over 18 °C. The paint surface should be clean and dry.

Application: Ardrox 2871 is applied by spraying with a piston-type pump and spray wand. Use with 3:1 or 10:1 pumps or pouring is also possible.

Apply to a thickness of 2 to 3 times the coating thickness or until the paint is uniformly covered. Do not apply too heavily, as sagging could occur. Personnel should always wear suitable protective clothing.

Paint Removal: In general, Ardrox 2871 should remain on the surface for 2 to 6 hours (dependent on temperature, coating thickness, type, etc.). If necessary to bubble the paint, Ardrox 2871 can be left on the surface for longer periods of time.

Note: Ardrox 2871 is designed for a single-coat application and so does not require reapplication in order to expedite removal.

Elimination: Ardrox 2871 and bubbled paint can be removed with a squeegee, brush rinsing with water, or equivalent method. Do not allow the softened paint to dry out as it may re-adhere to the substrate or surface.

Spot reapply the stripper to remaining painted areas if necessary and repeat the removal method. Follow up with a final rinse or wipe using water or wash with Ardrox 6484.

Dispose of waste according to local procedure.

EFFECT on MATERIALS

Ardrox 2871 is safe for aluminum, titanium, magnesium, and most types of steel. Not to be used on windows or composites.

STORAGE

Ardrox 2871 should be protected from freezing, preferably stored between 10 and 35 °C. Store in the original container. Do not use pumps with steel, brass, or zinc components that can make contact with the product. Do not return any used or unused Ardrox 2871 to the original container.

SAFETY GUIDANCE

Before operating the process described, it is important that this complete document together with any relevant safety data sheets be read and understood. Do not store used Ardrox 2871 and/or removed coatings in closed containers until all reaction has ceased. Avoid contacting materials containing solvable chromium.

Labor and environmental protection: All local and national regulations on the transport, storage, use, and waste treatment of chemicals in concentrated or diluted form and as working solutions must be obeyed.

Further specific information on the products can be found in the EC safety data sheets supplied. The user should also pay strict attention to information and hazard symbols shown on product labels.

WASTE DISPOSAL

All waste waters must be treated in accordance with national legislation and local regulations prior to discharge to the sewer.


ISO 9001:2000 FM 93653

Suggestion Of Other Products Your Company May Use:

• Cleaners

• Etchants

• Deoxidizers

• Rust Preventatives

• Metalworking Fluids(coolants and lubricants)

• Waste Water Treatment Chemicals

• Floor Cleaners and Maintenance Products

• Process Equipment/Control Systems

DISTRIBUTED BY NALTIC INDUSTRIALS AN AUTHORIZED DISTRIBUTOR FOR THE USA

Chemetall US, Inc. (“Chemetall”) warrants that products described within its official technical papers will conform with its published specifications. The products supplied by Chemetall and information related to them are intended for use by buyers having necessary industrial skill and knowledge. Buyers should undertake sufficient verification and testing to determine the suitability of the Chemetall materials for their own
purpose. Since buyer’s conditions of use of products are beyond Chemetall’s control, Chemetall does not warrant any recommendations and information for the use of such products.

CHEMETALL DISCLAIMS ALL OTHER WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE IN CONNECTION WITH THE USE OF ITS PRODUCTS.

Please contact us directly for a complete and official Chemetall Technical Data Sheet and/or MSDS in PDF.

Contact us: Office (888) 891-0077
email: 411@naltic.com

Headquarters
NALTIC Industrials, LLC
299 S Main St Suite 1300
Salt Lake City, UT 84111
USA