New Phased Array calibration block used for angle beam verification, probe angle exit point, calibration for wedge delay, sensitivity, DAC/TCG for thicknesses up to 2”, and crack sizing. The three radii (0.500”, 1.000”, and 2.000”) allow for velocity and sound path calculations. Block contains five holes at 3/64” diameter drilled through the 1.000” width, located at .100, .200, .400, .600, .800, 1.200, 1.400, 1.600, 1.800, and 1.900” from the respective scanning surface. Generous hole spacing eliminates “ghost” images from adjacent holes. Also includes an engraved scale from 30° to 70° associated with the .800” hole. Dimensions: 18.0” x 2.0” x 1.0”. In accordance with PH Tool Drawing No. 10173. Designed jointly by PH Tool LLC and Davis NDE. 

Pricing

Steel $1679.00
Alum $1679.00
SS $2241.00
Titanium Call

Mini PACSTM Block is a smaller, portable version of the original PACSTM Block. The block includes a total of four holes at 3/64″ diameter drilled through the 1.000″ width, located at .200, .400, .600, .700, .800, .900, 1.100, and 1.300″ from the respective scanning surface. Dimensions: 1.500″ tall x 1.000″ wide x 10.00″ long. In accordance with PH Tool Drawing No. 10192. Designed jointly by PH Tool LLC and Davis NDE. 

Pricing

Steel $893.00
Alum $893.00
SS $1190.00
Titanium Call

The PACSTM Notch Block has been specially designed for use with Phased Array instruments used for sizing of OD and ID-connected cracks. The block contains four EDM slots at depths of 20, 40, 60, and 80% and a width of .031″. Standard thickness is 1.000″; however, other sizes can be ordered. Dimensions: 1.000″ thick x 2.000″ wide x 7.00″ long. In accordance with PH Tool Drawing No. 10210. Designed jointly by PH Tool LLC and Davis NDE.

Pricing

Steel $1966.00
Alum $1966.00
SS $2657.00
Titanium Call

The PH Tool ASTM E2491 Phased Array Assessment Block is a general purpose Phased Array calibration block used for beam characterization and evaluation of system performance characteristics. Use it as baseline block to determine long-term instrument performance changes, generate DAC curves, and evaluate linear/angular resolution, focusing ability and beam steering capability. With a variety of targets, this small, lightweight block is also perfect for customer demonstrations of phased array ultrasonics capabilities. This block is also referred to as a “Type B” block. Dimensions: 150mm x 100mm x 25mm. In accordance with ASTM E2491 and PH Tool Drawing No. 10208. 

Pricing

Steel $1703.00
Alum $1234.00
SS $2384.00
Titanium Call

The Phased Array “Type A” Calibration Block is used during the initial setup and calibration of a phased array ultrasonic unit. This block can be used to perform tasks such as beam angle verification, calibration for wedge delay, sensitivity calibration, performing DAC/TCG, and more. This block has similar dimensions to an IIW-Type Block, but has been specially- engineered for phased array applications. Blocks include both 50.0mm and 25.0mm radii, (19) through holes at 1.0mm diameter, (1) through hole at 2.0mm diameter, (4) FBHs at 2.0mm diameter x 2.0, 4.0, 6.0, and 8.0mm deep, (4) FBHs at 4.0mm diameter x 1.0, 3.0, 5.0, and 7.0mm deep, (3) FBHs at 2.0mm diameter x 3.0mm deep machined into the 25mm radius, and (4) EDM notches at 0.1, 0.2, 0.3, and 0.4mm deep x 0.5mm wide x 25.0mm long. Block dimensions are 25.0mm thick x 100.0mm tall x 300.0mm long. In accordance with PH Tool Drawing No. 10217. 

Pricing

Steel $1540.00
Alum $1540.00
SS $2078.00
Titanium Call

This new Phased Array calibration block design by PH Tool contains all of the required features on the ASME Section V, Article 4 Basic Calibration Block yet spaces the holes out on a longer, narrower block. The block contains three holes at 3/32” diameter drilled through the 1.500” width, located at 1/4T, 1/2T, and 3/4T. It also contains two EDM notches at 2% deep x .010” wide x 1.500” long on opposite surfaces of one end. Dimensions: 14.0” x 1.5” x .75” thick. In accordance with PH Tool Drawing No. 10178. 

Pricing

Steel $927.00
Alum $927.00
SS $1253.00
Titanium Call

This special Phased Array version of the popular NAVSHIPS block solves the problem of too many holes interfering with one another. The block contains four holes at 3/64” diameter drilled through the 1.250” width. The holes are located at .250, .750, 1.250, 1.750, 2.250, and 2.750”. Dimensions: 12.0” x 3.0” x 1.25”. In accordance with PH Tool Drawing No. 10168. 

Pricing

Steel $684.00
Alum $684.00
SS $1201.00
Titanium Call